HVP-KV58F

The adc16_interrupt example shows how to use interrupt with ADC16 driver.In this example, user should indicate a channel to provide a voltage signal (can be controlled by user) as the ADC16'ssample input. When running the project, typing any key into debug console would trigger the conversion. ADC interrupt would be asserted once the conversion is completed. In ADC ISR, the conversion completed flag would be cleared by reading the conversion result value. Also, the conversion result value is stored, and the ISR counter is increased. These information would be printed when the execution return to the main loop.The point is that the ADC16 interrupt configuration is set when configuring the ADC16's conversion channel. When in software trigger mode, the conversion would be launched by the operation of configuring channel, just like writing aconversion command. So if user wants to generate the interrupt every time the conversion is completed, the channel's configuration with enabling interrupt setting would be used for each conversion.

The adc16_polling example shows the simplest way to use ADC16 driver.In this example, user should indicate a channel to provide a voltage signal (can be controlled by user) as the ADC16'ssample input. When running the project, typing any key into debug console would trigger the conversion. The execution would check the conversion completed flag in loop until the flag is asserted, which means the conversion is completed. Then read the conversion result value and print it to debug console.Note, the default setting of initialization for the ADC converter is just an available configuration. User can changethe configuration structure's setting in application to fit the special requirement.The auto-calibration is not essential but strongly recommended. It can help to adjust the converter itself and improvethe ADC16's performance.

CMSIS-Driver defines generic peripheral driver interfaces for middleware making it reusable across a wide range of supported microcontroller devices. The API connects microcontroller peripherals with middleware that implements for example communication stacks, file systems, or graphic user interfaces. More information and usage methord please refer to http://www.keil.com/pack/doc/cmsis/Driver/html/index.html.The cmsis_uart_edma_transfer example shows how to use uart cmsis driver with EDMA:In this example, one uart instance connect to PC through uart, the board willsend back all characters that PC send to the board.Note: The example echo every 8 characters, so input 8 characters every time.

CMSIS-Driver defines generic peripheral driver interfaces for middleware making it reusable across a wide range of supported microcontroller devices. The API connects microcontroller peripherals with middleware that implements for example communication stacks, file systems, or graphic user interfaces. More information and usage methord please refer to http://www.keil.com/pack/doc/cmsis/Driver/html/index.html.The cmsis_uart_interrupt_transfer example shows how to use uart cmsis driver in interrupt way:In this example, one uart instance connect to PC through uart, the board willsend back all characters that PC send to the board.Note: The example echo every 8 characters, so input 8 characters every time.

The CRC Example project is a demonstration program that uses the KSDK software to generate checksumsfor an ASCII string. Several CRC protocols are implemented using the CRC driver API.

The DAC / ADC demo application demonstrates the use of the DAC and ADC peripherals. This application demonstrates how toconfigure the DAC and set the output on the DAC. This demo also demonstrates how to configure the ADC in 'Blocking Mode'and how to read ADC values.

The DAC / ADC demo application demonstrates the use of the DAC and ADC peripherals. This application demonstrates how toconfigure the DAC and set the output on the DAC. This demo also demonstrates how to configure the ADC in 'Blocking Mode'and how to read ADC values.

The EDMA memory to memory example is a simple demonstration program that uses the SDK software.It excuates one shot transfer from source buffer to destination buffer using the SDK EDMA drivers.The purpose of this example is to show how to use the EDMA and to provide a simple example fordebugging and further development.

The EDMA memory to memory example is a simple demonstration program that uses the SDK software.It excuates one shot transfer from source buffer to destination buffer using the SDK EDMA drivers.The purpose of this example is to show how to use the EDMA and to provide a simple example fordebugging and further development.

The FTM project is a simple demonstration program of the SDK FTM driver to use FTM as a timer.It sets up the FTM hardware block to trigger an interrupt every 1 millisecond.When the FTM interrupt is triggered a message a printed on the UART terminal.