MSPM0L1303
-
Core
Cortex-M0+, 32 MHz
-
Family
MSPM0L11XX_L13XX Series
-
Sub-Family
MSPM0L130X
-
CMSIS Pack
MSPM0L11XX_L13XX_DFP
The MSPM0L134X and MSPM0L130X microcontrollers (MCUs) are part of MSP's
highly-integrated, ultra-low-power 32-bit MCU family based on the enhanced
Arm® Cortex®-M0+ core platform operating at up to 32-MHz frequency.
These cost-optimized MCUs offer high-performance analog peripheral integration,
support extended temperature ranges from -40°C to 125°C, and operate with
supply voltages ranging from 1.62V to 3.6V.
The MSPM0L134X and MSPM0L130X devices provide up to 64KB embedded Flash program
memory with up to 4KB SRAM. They incorporate a high speed on-chip oscillator
with an accuracy of ±1%, eliminating the need for an external crystal.
Additional features include a 3-channel DMA, 16 and 32-bit CRC accelerator,
and a variety of high-performance analog peripherals such as one 12-bit 1MSPS
ADC with configurable internal voltage reference, one high-speed comparator
with built-in reference DAC, two zero-drift zero-crossover op-amps with
programmable gain, one general-purpose amplifier, and an on-chip temperature
sensor. These devices also offer intelligent digital peripherals such as
four 16-bit general purpose timers, one windowed watchdog timer, and a
variety of communication peripherals including two UARTs, one SPI, and two I2C.
These communication peripherals offer protocol support for LIN, IrDA, DALI,
Manchester, Smart Card, SMBus, and PMBus.
| Core |
Processor Cortex-M0+ |
|---|---|
| Maximum Clock Frequency | 32 MHz |
| Memory Protection Unit | NO_MPU |
| Floating Point Unit | NO_FPU |
| Trust Zone | |
| Digital Signal Processor | |
| CortexM Vector Extensions | |
| Endian | Little-endian |
| Features | View features |
Processor
Cortex-M0+, 32 MHz
-
I/O Zero-drift, zero-crossover chipper op-amp (OPA) 2 x Zero-drift, zero-crossover chipper op-amp (OPA) General-purpose amplifier (GPAMP) 1 x General-purpose amplifier (GPAMP) High-speed comparator (COMP) with 8-bit reference DACs 1 x High-speed comparator (COMP) with 8-bit reference DACs Configurable 1.4V or 2.5V internal shared voltage reference (VREF) 1 x Configurable 1.4V or 2.5V internal shared voltage reference (VREF) 1MSPS analog-to-digital converters with up to 10-ch (ADC) 10-channel x 12-bit 1MSPS analog-to-digital converters with up to 10-ch (ADC) General purpose I/Os, including some 5-V tolerant 28 General purpose I/Os, including some 5-V tolerant -
Timer 16-bit general purpose timer supporting low power operation in STANDBY mode 4 x 16-bit general purpose timer supporting low power operation in STANDBY mode Window-watchdog timer 1 x Window-watchdog timer -
Communication I2C interface supporting up to FM+ (1Mbps), SMBus/PMBus, and wakeup from STOP mode 2 x I2C interface supporting up to FM+ (1Mbps), SMBus/PMBus, and wakeup from STOP mode SPI interface 1 x 32 Mbit/s SPI interface UART inteface, one supporting LIN, IrDA, DALI, Smart Card, Manchester, and three supporting low-power operation in STANDBY mode 2 x 0 bit/s UART inteface, one supporting LIN, IrDA, DALI, Smart Card, Manchester, and three supporting low-power operation in STANDBY mode -
Core features Nested Vectored Interrupt Controller (NVIC) Nested Vectored Interrupt Controller (NVIC) with 32 interrupt sources Direct Memory Access (DMA) 3-channel Direct Memory Access (DMA) -
Memory Up to 64KB Flash memory x Up to 64KB Flash memory Up to 4KB SRAM x Up to 4KB SRAM -
Clock Internal 4-32MHz oscillator with +-1% accuracy (SYSOSC) x Internal 4-32MHz oscillator with +-1% accuracy (SYSOSC) Internal 32kHz oscillator (LFOSC) x Internal 32kHz oscillator (LFOSC) -
Power RUN0, RUN1, RUN2, SLEEP0, SLEEP1, SLEEP2, STOP0, STOP1, STOP2, STANDBY0, STANDBY1, SHUTDOWN 12 RUN0, RUN1, RUN2, SLEEP0, SLEEP1, SLEEP2, STOP0, STOP1, STOP2, STANDBY0, STANDBY1, SHUTDOWN Operating Voltage 1.62 V .. 3.6 V Operating Voltage -
Spec Extended Operating Temperature Range -40 °C .. +125 °C Extended Operating Temperature Range